manualshive.com logo in svg

ADTRAN 1202155L1, User Manual, Page: 28 / 146

Share
Download
ADTRAN 1202155L1 User Manual Download Page 28

Chapter 1. Introduction

1-4

TDU 120e User Manual

61202156L2-1A

TDU 120e OPTION MODULES

Some of the option modules available for the TDU 120e 
are:

DSX-1

Provides a short haul T1 interface for operation with a 
PBX (Terminal Interface).

Full Drop and Insert

Permits the dropping of data and insertion of new data 
into the same DS0 time slot.

This module includes a long haul DS-1 interface. It can 
also be used as a second DS-1 interface to provide an up 
to 3 MB aggregate throughput.

Nx56/64 serial interface

Provides a V.35 serial interface in either single or dual 
versions.

Voice interface

Provides 2 or 4 channels FXS/FX0/E&M.

OCU DP

Interfaces to DDS or 4-wire Switched 56, dual or single 
versions.

DSU DP

Provides two sync or async ports (EIA-232 or V.35).

Dial backup

Allows for backup of data upon network T1 failure.

U-BR1TE

Allows ISDN lines to be extended over a T1 line.

Summary of Contents for 1202155L1



















































































































































Reviews:

No comments