ADTRAN 1202155L1 Page 122 User Manual Download

Page: 122 / 146

Appendix A. Understanding SNMP

A-6

TDU 120e User Manual

61202156L2-1

SNMP MIB Browser Configuration

The following steps are required to configure Network
Manager MIB variable access through the TDU 120e:

Step

Action

Load the desired product MIBs on the network
management station.

Example

If the administrator is managing TDU 120e and ISU 512
devices, load

TDU 120e.MIB

ISU512.MIB

, and

RFC1406.MIB

Create device entries in the NMS database for all units
that are to be managed through the TDU 120e.

The host unit should be configured as the Proxy agent for
the external units. The IP address or host name used for
the proxy designation is that of the TDU 120e.

Set community names in the device’s entries for external
units to the TDU 120e community name with the device
Unit ID appended.

See

TDU 120e SNMP ACCESS

on page A-4 for more

information.

Set the device timeout for all device entries in the NMS
device database to five seconds, including the host unit.

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands

ADTRAN 1202155L1, User Manual

Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands