ADTRAN 1202155L1 User Manual Download Page 100

Page: 100 / 146

Chapter 7. Test Menu

7-4

TDU 120e User Manual

61202156L2-1

No Loopback

Deactivates the loopback. Scroll to select a setting and
press

Enter

to record the setting.

Remote Loopback

Activates the same loopbacks as

OCAL

OOPBACK

, but at

the far end.

Uses either the inband loopup code as specified by ANSI
T1.403 for line loopback (ATT In-Band LLB), or the FDL as
specified in ANSI T1.403 for payload and line loopback
codes.

The following options are available:

ATT In-Band LLB

Activates the line loopback using inband code.

ANSI FDL PLB

Initiates the transmission of an FDL payload loopup code
toward the far end.

ANSI FDL LLB

Initiates the transmission of an FDL line loopup code
toward the far end.

ANSI FT1 LLB

Initiates the transmission of an FT1 loopback using the
inband code described in T1.403.

No Loopback

Deactivates the loopback.

Remote Loopback can only be used with Fractional T1 if the ANSI FT1 LLB is
selected.

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

ADTRAN 1202155L1, User Manual, Page: 100 / 146

Search results

Summary of Contents for 1202155L1

Reviews: