ADTRAN 1202155L1 Page 48 User Manual Download

Page: 48 / 146

Chapter 3. Operation

3-6

TDU 120e User Manual

61202156L2

Menu Options

The opening menu is the access point to all other opera-
tions. Each

AIN

menu item has several functions and

submenus to identify and access specific parameters.

Status

Displays all relevant information for the network and
DTE interfaces. For detailed information on status
options, see

Chapter 4, Status Menu.

Config (Configuration)

Displays and sets the TDU 120e operational configura-
tion, including all network interface parameters, the allo-
cation of the DS0s, and the port parameters. For detailed
information on configuration options, see

Chapter 5, Con-

figuration Menu.

Util (Utilities)

Displays and sets system parameters. For detailed infor-
mation on utility options, see

Chapter 6, Utility Menu.

Test

Initiates different types of unit tests and displays test
results in the terminal window. For detailed information
on test options, see

Chapter 7, Test Menu.

Remote Access Menu

Displays Telnet menus for a remote device. For detailed
information, see

Chapter 8, Remote/Management Menus.

Only one Telnet/terminal session may be active at a time.

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands

ADTRAN 1202155L1, User Manual

Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands