ADTRAN 1202155L1 Page 31 User Manual Download | Manualshive

Page: 31 / 146

background image

61202156L2-1

TDU 120e User Manual

2-1

Chapter 2

Installation

UNPACK, INSPECT, POWER UP

Receipt Inspection

Carefully inspect the TDU 120e

for any shipping damag-

es. If you suspect damage, file a claim immediately with
the carrier and then contact ADTRAN Customer Service
(see the front section of this manual for contact informa-
tion). If possible, keep the original shipping container for
use in shipping the TDU 120e back for repair or for verifi-
cation of damage during shipment.

ADTRAN Shipments

The following items are included in the ADTRAN ship-
ment:

•

The TDU 120e

•

2-line interface cables: A 15-foot, 8-position modular
to 8-position modular

•

A DB-25 to modular adapter

•

A 6-foot, 8-position modular cable for connection to
the chain-in port

•

The user manual

«
...
29
30
31
32
33
...
»

Summary of Contents for 1202155L1



















































































































































Reviews:

No comments

Related manuals for 1202155L1

Brand: Keithley Pages: 35

Brand: Malmbergs Pages: 20

Brand: Meterman Pages: 14

Brand: Kaiweets Pages: 26

Brand: Besantek Pages: 12

Brand: RS Components Pages: 22

Brand: Tenma Pages: 8

Brand: Mastech Pages: 10

Brand: Mastech Pages: 12

Brand: Mastech Pages: 12

Brand: Giga-tronics Pages: 40

DMX4ALL ArtNet-DMX Mux24

Brand: Artistic Licence Pages: 20

Brand: Maxwell Digital Multimeters Pages: 32

Brand: IDEAL Pages: 14

Brand: Wavetek Pages: 32

NMEA Multiplexer

Brand: Raymarine Pages: 16

Brand: Keithley Pages: 221

Brand: IDEAL Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands