ADTRAN 1202155L1 Page 123 User Manual Download

Page: 123 / 146

Appendix A. Understanding SNMP

61202156L2-1

TDU 120e User Manual

A-7

SNMP MIB Files

The TDU 120e supports several standard MIBs including:

•

MIB-II (RFC-1213),

•

DS1 T1/E1 MIB (RFC-1406), and

•

the Ethernet MIB (RFC-1643).

It also supports several ADTRAN enterprise-specific
MIBs including:

•

ADTRAN Product MIB (ADTRAN.MIB),

•

ADTRAN DS1 extensions MIB (ADS1.MIB), and

•

all TSU/TDU Enterprise MIBs, such as TDU
120e.MIB.

The standard MIB files are usually included with most
SNMP network management software. The latest version
of the ADTRAN enterprise specific MIBs are available in
the following places:

•

ADTRAN anonymous ftp site: ftp.adtran.com

•

Dial-up: BBS (256 -963-8169).

•

Adtran web site: http://www.adtran.com.

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands

ADTRAN 1202155L1, User Manual

Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands