ADTRAN 1202155L1 Page 61 User Manual Download

Page: 61 / 146

Chapter 4. Status Menu

61202156L2-1

TDU 120e User Manual

4-7

DS-1 (0.2) Menu Items (DS-1 Errors)

CRC

An asterisk displays under the CRC if there are CRC
errors in extended superframe format (ESF) mode. If the
DS-1 is configured for D4 Frame format, the terminal dis-
plays

N/A

BPV

An asterisk displays under the

BPV

if the DS-1 detects

bipolar violations.

SLIP

An asterisk displays under the

SLIP

if the DS-1 detects

frame slips. This is caused by multiple clock sources in
the application.

FER

An asterisk displays under the FER if the DS-1 detects
frame bit synchronization errors.

Remote Port

EMOTE

ORT

displays the status of activity on the Con-

trol In remote port. This is useful for troubleshooting
communication sessions, and for verifying cabling.

Characters received at remote port

Unit ID received at remote port

CRC

Correct CRC received

Correct passcode received

Characters transmitted from the remote port

Summary of Contents for 1202155L1



















































































































































Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands

ADTRAN 1202155L1, User Manual

Search results

Summary of Contents for 1202155L1

Reviews:

Related manuals for 1202155L1

Brands by name

Popular brands