manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 98 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 98

Installation and User Manual

ADPRO FastTrace by Xtralis

86

Doc 11168_12

The 

Live

 option is primarily designed for use with access (entry/exit) points. A live video feed is 

displayed at VideoCentral.

The 

Quad

 option captures three alarm images in a user-defined period (defined under 

Camera

 

Settings/General

 tab) and displays the images at VideoCentral, along with a fourth pane which 

sequences through the three images to highlight movement.

4.3.15 Control Outputs

The 

Control Outputs

 option defines a number of parameters about the type and operation of the 

output circuits connected to the FastTrace. The outputs are ‘open collector’ transistor circuits 
used to generate a control signal (upon activation of an alarm) to activate third-party equipment 
at the remote site, for example a boom gate controller or a floodlight control device. 

Select the control output number from the displayed list. The number of control outputs available 
depends on the FastTrace Model number. The status of a control output is shown by a small icon 
to the left of the channel number.

•

A control output is

 free

 when the ‘empty’ icon is shown next to the number

•

The

 Connect

 button is used to enable a control output. A green tick is shown and details 

can be modified

•

To temporarily disable the use of a control output, the 

Disconnect 

button is used and a red 

cross is shown. For example, set Disconnect if maintenance is being performed on the unit 
under control.

Figure 85: Control Output Settings Menu

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments