manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 96 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 96

Installation and User Manual

ADPRO FastTrace by Xtralis

84

Doc 11168_12

The 

Duress

 option is designed to be used with silent panic alarms and will cause a 

Live and 

Quad

 alarm to be sent to VideoCentral. The Live alarm enables an event to be quickly displayed 

at the CMS and the Quad alarm ensures that video is captured at the instant the panic alarm is 
operated.

4.3.14 Presidium Inputs

The 

Presidium Inputs

 option enables the configuration of video outputs from a Presidium 

Intelligent Video System to the FastTrace video inputs.

Note: 

At least one Presidium Input must be configured. If there are no inputs configured, 
the following Presidium system alarms will not work at the FastTrace:

-

Presidium Operational 

-

Tamper alert

-

Over Temperature 

-

Communication to Presidium Lost 

-

Communication to Presidium Resumed

-

Presidium Fault

Note: 

When connecting a FastTrace to a Presidium, each FastTrace video input must be 
directly connected to a Presidium video output. Hence, if the Presidium has 20 
channels, a 20 channel FastTrace is required to operate all 20 channels.

Select the Presidium Input number from the displayed list. The status of an Presidium Input is 
shown by a small icon to the left of the channel number.

•

A Presidium Input is

 

unallocated when no name is shown next to the number.

Figure 82: Unallocated Icon

•

The

 Connect

 button is used to enable an Alarm Input. A green tick is shown and details can 

be modified.

To disable the use of an Alarm Input, the 

Disconnect 

button is used and a red cross is shown. 

For example, set Disconnect if maintenance is being performed in that area or the sensor is 
being replaced.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments