ADPRO ADPRO FastTrace Installation And User Manual Download Page 143

Page: 143 / 146

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

131

Audio Switch Interface

Audio In/Out to VM22A or third party Audio Switcher.

Bi-directional audio sent simultaneously with the video (full duplex).

Bandwidth: 300 Hz to 3.3 kHz.

Input impedance: >6 k ohms. Input level: 10 mV to 400 mV RMS (nom)

Output impedance: >6 k ohm. Output level: 315 mV (nom)

Serial Output for Channel Number sequencing.

Open drain outputs (binary coded hex) indicating the currently selected channel.

32V maximum, 100 mA maximum, output impedance <0.5 ohm

Refer to VM22A Audio Switcher manual for details of serial protocol.

Audio Connector

Direct connection via 9-pin screw connector.

Microphone: Differential impedance >3 k ohm

Single-ended impedance >6 k ohm

Nominal signal level is 100 uV to 10 mV rms.

Speaker: 1 Watt (max) into 8 ohm load.

Line In: Unbalanced input impedance >6 k ohm

Nominal signal level is 10 mV to 400 mV rms.

Line Out: Unbalanced output impedance = 600 ohm

Nominal level is 315 mV rms.

Power requirements

AC Operation 110 - 240 volts, 5A, 50 - 60 Hz

Construction & dimensions

Standard 19” rackmount, 3U high subrack to DIN4194.

482 mm (19”) W x 132 mm (5.25”) H x 280 mm (11”) D

Weight (fully configured
condition)

11 Kg (22 lb)

Temperature range

Operating range 0 degC to 40 degC (32 degF to 104 degF)

Humidity less than 90% non-condensing.

EMC Compliance

EMC Emission:

EN55022:1998 (CISPR 22:1997) / AS/NZS 3548:1995 + A1, A2 Class A Conducted and
radiated emissions

FCC Part 15 Class A Conducted and radiated emissions

EN61000-3-2:1995 Mains harmonic current emissions

EN61000-3-3:1995 Voltage fluctuations and flicker

EMC Immunity:

EN50130-4:1995 +A1 Alarm Systems Immunity

EMC Directive 89/336/EEC and carries CE marking

Safety Compliance

EN 60950:1992 +A1, A2, A3, A4, + A11

IEC60950: 1991 +A1, A2, A3 & A4

Low Voltage Directive 73/23/EEC and carries CE marking

UL Listed to US and Canadian Safety Standards

UL File Number E219750

Warranty

24-months on all components except Hard Disk Drive (HDD) units where manufacturers
warranty and conditions apply.

Function

Description

Summary of Contents for ADPRO FastTrace



















































































































































Search results

Summary of Contents for ADPRO FastTrace

Reviews:

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 143 / 146

Search results

Summary of Contents for ADPRO FastTrace

Reviews: