ADPRO ADPRO FastTrace Installation And User Manual Download Page 101 | Manualshive

Page: 101 / 146

ADPRO ADPRO FastTrace Installation And User Manual Download Page 101

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

89

Audio Out Volume

Options:

Range 0 to 15

Factory Default:

2

Choose a volume level between 0 (lowest) and 15 (highest) to suit the operational environment.

4.3.17 Arming / Disarming

Figure 87: Arming/Disarming Menu

The Arm/Disarm properties allow a user to configure the Arm/Disarm Tamper Protection settings
and Arm/Disarm Local Indication features of FastTrace.

Alternative Arm/Disarm Input

This setting allows an unused alarm input to be configured as the access / secure (arm / disarm)
input on the FastTrace. This provides a tamper detected access / secure input as required in the
BS8418 regulations.

Whenever a tamper has occurred on the Arm/Disarm point, the FastTrace will initiate a Dial Out
and record a tamper event. Once connected to VideoCentral, the tamper event is sent. This
event will be identifiable as a tamper event on the Arming Device.

To configure:

Use an Alarm Input as the Arm / Disarm input

: Check this box if using this feature.

Channel

: Select an unused alarm input for the access / secure input from the drop-down list. The

alarm input will be marked as not-usable in the alarm input configuration.

Name

: Type a name for the alternative access / secure input.

«
...
99
100
101
102
103
...
»

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments