manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 78 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 78

Installation and User Manual

ADPRO FastTrace by Xtralis

66

Doc 11168_12

Figure 66: Advanced Serial Communications

Local IP Address

Factory Default:

 192.168.254.1

Sets the

 Local IP Address

 assigned to FastTrace’s COMMS port. This address is used by the 

PPP messaging software and is 

NOT 

the same as the Ethernet Properties setting or of 

any 

other device on the network

.

When multiple FastTrace units are to be accessed from a single VideoCentral system, each 
FastTrace unit MUST have a unique Local IP Address (ie. do not leave at the factory default 
address) for each serial and ethernet connection.

For more information, please refer to:

Tech Tip 10470_00 - Unique IP Address Requirements, available on the website: 

www.xtralis.com/adpro

.

Caution: 

Contact Xtralis technical support for advice before entering data into: 

Enable PAP

, 

PPP Username

 or 

PPP Password

.

Enable PAP

Factory Default:

No

Set this checkbox to enable Password Authentication Protocol. PAP will authenticate the remote 
system during the PPP negotiations. The valid username and password are defined by the fields 
of PPP Username and PPP Password.

PPP Username

Option:

20 characters maximum.

The

 Username

 (or Site Name) that will be provided by PPP when negotiating a serial IP 

connection. It is only required when PAP is enabled. 

Note: 

The PPP Username is a function of the modem or TA and will also need to be set in 
the device.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments