manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 72 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 72

Installation and User Manual

ADPRO FastTrace by Xtralis

60

Doc 11168_12

4.3.6 Communications

The 

Communications

 menu provides configuration settings for the Ethernet and two serial 

communication ports.

Figure 63: Communications Menu

Ethernet Properties

A direct connection to a 10BaseT or 100BaseTX Ethernet network can be made via the Ethernet 
Port. To change this address, the Subnet Mask or Default Gateway address, click the 

Configure

 

button. 

Ethernet Settings

 are used to configure the TCP/IP parameters for a LAN or WAN 

connection.

Note: 

Always obtain Ethernet IP Address, Subnet Mask and Gateway details from the IT 
Manager responsible for the network where the FastTrace is installed. DO NOT 
CONNECT FASTTRACE TO THE ETHERNET UNTIL THESE SETTINGS HAVE 
BEEN MADE AND VERIFIED.

Important: To ensure correct network connectivity, please ensure FastTrace is 

connected to the network before being powered on. This enables the 
FastTrace unit to detect the correct network speed (10BaseT or 
100BaseT).

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments