manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 4 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 4

Installation and User Manual

ADPRO FastTrace by Xtralis

ii

Doc. 11168_12

The following icons are used in this document

Tradename statement

ADPRO is a registered trademark of Xtralis AG Pty Ltd.

Lightning or Related Voltage Surges

Damage or malfunction caused by lightning or related voltage surges may be excluded from the manufacturer’s warranty at the 
manufacturer’s discretion.

Safety Procedures
Installations in the United States of America and Canada

For systems installed in the United States of America and Canada the following requirement is applicable:

All equipment installations are required to be in accordance with the National Electrical Code (NEC) ANSI/NFPA 70 and the Canadian 
Electrical Code (CEC) Part 1, CAN/CSA C22.1.

If the power cord is not supplied with the ADPRO 

XXXProduct NameXXX

, select the proper power cord according to your local national 

electricity code.

USA: use a UL listed type SVT or SJT detachable power cord.
Canada: use a CSA certified detachable power cord.

Radio Interference

The ADPRO FastTrace complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may 
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired 
operation.

The ADPRO FastTrace complies with the electromagnetic emission limit requirements of AS/NZS CISPR22 and EN55022 Class A. In a 
domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Internal Lithium Battery

Caution: 

The ADPRO FastTrace contains an internal lithium battery.
There is danger of explosion if the battery is incorrectly replaced.
The battery is not user replaceable and can only be replaced by Xtralis or their Authorised Service Representative.

Compliance of Power Cord

Caution: 

If the power cord supplied with the ADPRO FastTrace is not suitable for your local power connection, do not modify the 
cord. Please purchase a power cord that has the safety approvals appropriate for your country.

Connection to Other Equipment

Caution: 

All interface ports on the ADPRO FastTrace must be only connected to other equipment or systems that are Safety 
Extra Low Voltage (SELV) rated. Failure to do so will invalidate the electrical safety approval and may cause injury or 
loss of life

Convention

Description

Caution: This icon is used to indicate that there is a danger to equipment. The danger could be loss of data, 
physical damage, or permanent corruption of configuration details.

Warning: This icon is used to indicate that there is a danger of electric shock. This may lead to death or 
permanent injury.

Warning: This icon is used to indicate that there is a danger of inhaling dangerous substances. This may 
lead to death or permanent injury.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments