manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 115 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 115

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

103

Activate Control Output

When checked, the control output correlating to the camera channel number currently being 
programmed will be activated for a period as defined in the 

Alarm Input

 / 

Hold Time

 (refer to 

Alarm Input Settings

 on page 82) upon full activation of an event. Refer to 

Control Outputs

 on 

page 86.

Note: 

If the assigned Control Output number has been specified for 

Manual Operation

, 

then an error message will be displayed.

Dial Out on Event

When checked, an Event on this camera channel will cause the FastTrace system to send an 
alert with details of the event to the CMS, following the rules previously defined in 

Communications

 / 

Call List

.

Note: 

On connection to the CMS, up to a total of six events with images will be sent per 
connection. All subsequent events are sent without images until a new connection is 
established.

Dial Out Only When Armed (Secure)

: Unchecking this setting can be used to override the 

Armed / Disarmed status of the system for this particular camera in this particular mode, 
effectively creating a 24-hour zone (i.e. can be used for Panic Buttons etc). 

Important: Use extreme caution when using this setting in conjunction with 

Activity Detection triggered events, as this can cause many false / 
nuisance alarms and block access to programming.

Dial Out on Video Loss

Options:

Yes, No

Factory Default: 

Yes

When checked, FastTrace will dial-out, sending an alert to the CMS, in the event of lost video on 
this camera channel due to camera disconnection or output failure. Note that this operation is 
looking for presence of video by the Sync Pulse - this is not a Contrast (or 'Black-bag') alarm.

Important: If the camera Recording Type has been set to ‘Do Not Record’, then a 

‘Dial Out on Video Loss’ will not occur. There must be a Recording 
Mode selected for a dial out to occur.

Dial Out on Invalid Contrast

Options:

Yes, No

Factory Default: 

No

Select the 

Dial out on invalid contrast

 checkbox if operators are to be notified if a Contrast 

Alarm condition occurs on this camera. A contrast alarm will occur if the camera contrast level 
changes to a level that lies outside of a user definable range. 

Important: If the camera Recording Type has been set to ‘Do Not Record’, then a 

‘Dial Out on Invalid Contrast’ will not occur. There must be a Recording 
Mode selected for a dial out to occur.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments