manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 133 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 133

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

121

No video from camera

User

Video restored on camera

User

Contrast alarm on camera

User

Normal contrast on camera

User

ATM transaction

User

ATM transaction started

User

ATM transaction finished

User

Started mode

User

Finished mode

User

Control output active

User

Control output inactive

User

Alert generated

Maintainer

This log is not new, but any alerts that do not produce 
one of the alert-specific messages will result in this log 
getting generated. There should be no such alerts, so we 
should never see this log entry.

Alert sent to user

Maintainer

Alert acknowledged

Maintainer

Alert discarded

Maintainer

Entry delay started

User

Entry delay finished

User

Exit delay started

User

Exit delay finished

User

No video alert generated

Maintainer

A No-Video alert was generated.

Vmd alert generated

Maintainer

A VMD alert was generated.

Contrast alert generated

Maintainer

A contrast alert was generated.

Alarm input alert generated

Maintainer

An alarm input alert was generated.

Alarm input tamper alert generated

Maintainer

An alarm input tamper alert was generated.

Digital input alert generated

Maintainer

A digital input alert was generated.

POS ATM alert generated

Maintainer

A POS/ATM alert was generated

Log Title

Visibility

Comments

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments