ADPRO ADPRO FastTrace Installation And User Manual Download Page 84 | Manualshive

Page: 84 / 146

ADPRO ADPRO FastTrace Installation And User Manual Download Page 84

Installation and User Manual

ADPRO FastTrace by Xtralis

72

Doc 11168_12

PTZ Settings

Serial Options:

360vision, Amux IEC, Baxall ZMX, Baxall ZTX, Baxall ZTX7, BBV, Burle,
COHU, Conway, CS Lilin, Dennard 2050, Diamond, Digital Sprite, Elbex,
Ernitec, GPS, Grundig, Harris, JVC, Kalatel CyberDome, Kalatel KTD 12x,
Mark Mercer, Molynx, Pacom 2018, Panasonic (Conventional), Panasonic
(New), Pelco Coaxitron 4800_8_E_1, Pelco_D_2400_8_N_1,
Pelco_D_4800_8_N_1, Pelco P 4800_8_N_1, Pelco P 9600_8_N_1, Philips,
Samsung (Lens only), Sensormatic, Sensormatic Controller, Sensormatic
SpeedDome VII, Siemens, Synectics, Unidex, VCL, Vantage Juno, Vicon,
Video Switch, Video Technical Fastrax-P, Vista PowerDome, Xeno Neodome.

Down the Coax Options:Baxall Coax Alt, Baxall Coax Std, BBV Coax, Pelco Coax Ext.

Factory Default:

No PTZ

When using Pan/Tilt/Zoom (PTZ) cameras or telemetry stations, the type of device must be set.
Information to control a serial PTZ unit will be sent via the PTZ port connector on the rear panel.

To use a PTZ camera, individual Camera Settings require the

‘This Camera has a PTZ station’

checkbox to be set.

FastTrace also incorporates the ability to use a ‘Down the Coax’ module to send control signals
to some telemetry camera stations, down the same coaxial cable that is used to transmit video to
the FastTrace.

This module can only be fitted at the factory or at your service centre.

Notes on PTZ settings:

•

Only one PTZ telemetry type can be selected on a FastTrace system (i.e. it is not possible
to select a combination of telemetry types for different cameras).

•

This setting only defines the telemetry protocol to be used by the system. Individual
cameras which have PTZ functionality must be set-up accordingly under the individual
camera setup.

Note:

Please refer to PTZ Tech Tips for connection and setup information on the website -

www.xtralis.com/adpro.

4.3.9 Cameras

Selecting the

Cameras

option displays a list of available video channels and any camera name

assigned to the channel.

The number of available channels will depend on the FastTrace Model number. The number list
directly relates to the video input number on the back plane of the FastTrace.

«
...
82
83
84
85
86
...
»

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments