manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 124 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 124

Installation and User Manual

ADPRO FastTrace by Xtralis

112

Doc 11168_12

Temperature Monitor

Figure 111: Temperature Management

FastTrace monitors the internal temperature of the hard disk drives and has the option of dialling 
the CMS and generating an alarm if the temperature exceeds an upper limit of 65°C.

If High Temperature Management is Enabled

When the internal temperature of any disk drive rises above the high temperature threshold, 
FastTrace will initiate an over-temperature condition and report this to VideoCentral. The 
FastTrace fault relay will activate during the over-temperature condition. The FastTrace will 
continue to operate normally after reporting the over temperature condition but urgent action 
must be taken to ensure that the ambient temperature complies with FastTrace's 40°C maximum 
operating temperature specification. Continued operation at a temperature exceeding the 
specified maximum may damage or reduce the useable life of FastTrace.

When the temperature falls below the low temperature threshold, the over-temperature condition 
will be cleared and the fault relay will de-activate. 

If High Temperature Management is Disabled

No over-temperature alarm will be received by VideoCentral and the fault relay will not activate 
for an over-temperature condition. The unit will continue normal recording. 

Note: 

It is recommended that only specified hard disk drives recommended by ADPRO 
personnel be used. If non recommended hard disk drives are installed, temperature 
information received from the drive used for temperature management may be 
erroneous, causing damage to the FastTrace and/or incorrect reporting of alarms.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments