manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 114 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 114

Installation and User Manual

ADPRO FastTrace by Xtralis

102

Doc 11168_12

If using the 

Only When ALL Inputs Occur

 logic, only the first pre-set on the list will be active. If 

another Alarm Input is configured for the same PTZ camera, its preset will not be available, and 
will be displayed with an (N/A) beside the Preset Position.

Note: 

Please refer to PTZ Tech Tips for connection and setup information on the website - 

www.xtralis.com/adpro

.

Editing a Detector’s Preset

To edit a detector’s preset:

1.

Double click the event input to be modified. The Event Input Settings dialog box is 
displayed.

Figure 100: Event Input Settings

The Type and Source selections are greyed out, enabling the operator to only change the PTZ 
Preset Settings.

2.

Enter the appropriate settings and click 

OK

.

Event Response

Once an Event has been declared, the 

Event Response

 settings are used to define the actions 

that will be taken in response to the Event.

Figure 101: Event Response Tab

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments