manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 117 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 117

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

105

For a connected user to release the Multi-Screen functionality, the user has to: 

•

select any video mode other than Multi-Screen (this includes Pause),

•

disconnect, or 

•

lose it to a more privileged user.

The highest privilege level is CMS Operator. All connected users will receive a notification when 
the Multi-Screen Status changes.

Guard Tour Settings

Guard Tour operation provides a sequence through cameras programmed on the FastTrace unit. 
Depending on the display configuration (single screen or 4, 7, 9, 10, 13, 16 or 20 way split) the 
system will display all cameras and sequence through on the screen, or sets of cameras will be 
displayed. For instance if 16 cameras are configured for Guard Tour operation and a 4 way split 
is chosen, then the display will sequence through the first four cameras, then swap to the next 
four cameras.

To select which cameras are included in the Guard Tour click on the 

Configure

 button.

Figure 103: Guard Tour Camera List

Check the cameras needed in the Guard Tour and also enter a Dwell Time.

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments