manualshive.com logo in svg

ADPRO ADPRO FastTrace, Installation And User Manual, Page: 75 / 146

Share
Download
ADPRO ADPRO FastTrace Installation And User Manual Download Page 75

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

63

Serial Communication Properties

There are two Serial Communication Ports for analogue telephone line or digital line connection 
for communications with VideoCentral. Modems are used for analogue line (PSTN) connections 
and terminal adaptors (TA) for digital lines (ISDN). The COMMS 1 port is fitted with a 25-pin D 
male connector. The COMMS 2 port is a 9-pin D male (refer to 

Table 3

 on page 29).

Note: 

The COMMS 2 port can be used for direct connections to a PC for local setup and 
for software upgrades. A Null Modem driver is provided in the VideoCentral 
installation CD.
Refer to Tech-Tip 11460 – Windows XP SP2 Issues (available on the website: 

www.xtralis.com/adpro

) for more information on the use of the Null Modem Cable.

The

 Serial Communications Port 1 Settings

 and 

Serial Communications Port 2

 

Settings

 

menus allow the operating parameters of the two serial ports to be configured to match the 
model of modem or terminal adaptor used.

Figure 65: Serial Communication Port Settings Menu

Summary of Contents for ADPRO FastTrace



















































































































































Reviews:

No comments