ADMtek ADM5120 Datasheet Download Page 49

Page: 49 / 112

ADM5120

4.2.4 IRQ_raw_status, offset: 0x40

Bits

Type Name

Description

Initial value

9:0 RO IRQ_raw_status[7

:0]

The status of the interrupt sources

before

masking.
1: the corresponding IRQ is active

31:10 RO Reserved

Not

Applicable

4.2.5 IRQ_enable, offset: 0x80

Bits

Type Name

Description

Initial value

9:0

IRQ_enable[7:0] The enable register is used to mask the

interrupt source.
1: enable the interrupt and allow the
interrupt request to MIPS.
Writing “0” has no effect.

31:10 RO Reserved

Not

Applicable

4.2.6 IRQ_enable_clear, offset: 0xc0

Bits

Type Name

Description

Initial value

9:0 RW IRQ_enable_clear

[7:0]

The clear bits of the IRQ_enable.
Writing “1” clear the corresponding bit of
IRQ_enable.
Writing “0” has no effect.

31:10

Reserved

Not

Applicable

4.2.7 Reserved, offset: 0x10

Bits

Type Name

Description

Initial value

31:0

Reserved

Not

Applicable

4.2.8 INT_Mode, offset: 0x14

ADMtek Inc.

4-2

Bits

Type Name

Initial value

9:0 RW INT_mode[9:0] The

interrupt type of the interrupt sources

.
1: the corresponding Interrupt port
generate the FIQ to MIPS
0: the corresponding Interrupt port
generate the IRQ to MIPS

31:10

Reserved

Not

Applicable

Summary of Contents for ADM5120

















































































































Search results

Summary of Contents for ADM5120

Reviews:

ADMtek ADM5120, Datasheet, Page: 49 / 112

Search results

Summary of Contents for ADM5120

Reviews: