manualshive.com logo in svg

ADMtek ADM5120, Datasheet, Page: 48 / 112

Share
Download
ADMtek ADM5120 Datasheet Download Page 48

ADM5120   

 

 

 

 

 

 

 

 

 

            Register Description 

 

4.2 

System and Interrupt Registers 

 

4.2.1  Interrupt Control Register Map 

 

Offset Address 

name 

Base + 00 

IRQ_status 

Base + 04 

IRQ_raw_status 

Base + 08 

IRQ_enable 

Base + 0c 

IRQ_enable_clear 

Base + 10 

Reserved 

Base + 14 

INT_mode 

Base + 18 

FIQ_status 

Base + 1c 

IRQ_test_source 

Base + 20 

IRQ_source_sel 

Base + 24 

INT_level  

Note

: Base = 0x1220_0000 

4.2.2.  Interrupt Request Source Description 

 

Bit  

Name 

Description 

[9] 

Sw_int 

Switch interrupt, refer to B+B0, B+B4 

[8] 

PCI 2 

PCI INT2  

[7] 

PCI 1 

PCI INT1 

[6] 

PCI 0 

PCI INT0 

[5] 

Intx_1 

Internal interrupt 1, refer to GPIO[4] is the source 

[4] 

Intx_0 

Internal interrupt 0, refer to GPIO[2] is the source 

[3] 

USB 

USB interrupt source 

[2] 

UART1 

UART1 interrupt source 

[1] 

UART0 

UART0 interrupt source 

[0] 

timer 

Timer interrupt, refer to B+F0 and B+F4 

 

Note

:   Only support level sensitive interrupts. 

The external interrupt level, active high or low can be programmed 

 
 

4.2.3  IRQ_status, offset: 0x00 

 

ADMtek Inc. 

 

 

4-1   

Bits 

Type   Name  

Description 

Initial value 

9:0 

RO 

IRQ_status[7:0] 

The status of the interrupt sources 

after

 

masking.  
1: the corresponding IRQ is active, and 
generate the interrupt to MIPS 

0 

31:10 RO  Reserved 

 

0 

Summary of Contents for ADM5120

















































































































Reviews:

No comments