ABB OmniCore Operating Manual Download

Page: 201 / 266

Signal state

Signal

BCERR

BCWAR

BCACT

Interrupted brake check test, program pointer moved from BrakeCheck routine

Signal state

Signal

BCOK

BCERR

BCWAR

BCACT

Configure system parameters

About the system parameters

The configuration of system parameters required for a robot system should be
made before running the brake check.

Note

The controller must be restarted after changing the system parameters.

Type Mechanical Unit

All mechanical units for additional axes that shall be supervised must have the
parameters

Activate at Start Up

and

Deactivation Forbidden

set to On. (Supervised

mechanical units must always be active.)

Type Arm

If an axis should be excluded from brake check, set the parameter

Deactivate

Cyclic Brake Check for axis

to On.

Type Brake

If brake check is executed on an additional axis, a lowest safe brake torque must
be defined. A 5% margin is added during the test for setting the fail limit. The
parameter used is

Max Static Arm Torque

defined in Nm on motor side. A warning

limit is set with a higher torque value (depending on the brake).

Operating manual - OmniCore

201

3HAC065036-001 Revision: J

6 Programming and testing

6.10.8 Brake check service routine

Continued

Summary of Contents for OmniCore










































































































































































































































































Search results

Summary of Contents for OmniCore

Reviews:

Related manuals for OmniCore

Brands by name

Popular brands

ABB OmniCore, Operating Manual

Search results

Summary of Contents for OmniCore

Reviews:

Related manuals for OmniCore

Brands by name

Popular brands