ABB IRB 1660 Product Manual Download Page 334

Page: 334 / 398

Note

Action

Shown in the figure

Location of gearbox

unit, axes 1-2 on page 329

Fit a new

VK-cover

to the base of the robot.

Spare part no. is specified in

Required

equipment on page 330

CAUTION

The gearbox unit weighs 120 kg.
The base weighs 81 kg.
All lifting accessories used must be sized
accordingly!

Fit the

lifting slings

to the base/gearbox unit,

turn it right side up and move it to the install-
ation site.

Attachment bolts and the tightening
torque are specified in section

Attachment

bolts, specification on page 69

Secure the base to the foundation.

Detailed in section

Refitting, complete

arm system on page 181

Refit the complete arm system.

Detailed in sections:

•

Refitting the motor axis 1 on
page 259

•

Refitting, motor axis 2 on page 265

Refit the motors, axes 1 and 2.

Detailed in section

Performing a leak-

down test on page 154

Perform a leak-down test.

See,

Technical reference manual - Lubric-

ation in gearboxes

Fill the two gearboxes with oil.

Seal and paint the joints that have been
opened. See

Cut the paint or surface on the

robot before replacing parts on page 159

Note

After all repair work, wipe the robot free
from particles with spirit on a lint free cloth.

Pendulum Calibration is described in

Op-

erating manual - Calibration Pendulum

enclosed with the calibration tools.

Recalibrate the robot.

Axis Calibration is described in

Calibrat-

ing with Axis Calibration method on
page 349

General calibration information is included
in section

Calibration on page 337

DANGER

Make sure all safety requirements are met
when performing the first test run. These
are further detailed in the section

First test

run may cause injury or damage on
page 28

334

Product manual - IRB 1600/1660

3HAC026660-001 Revision: W

4 Repair

4.7.1 Replacement of gearbox, axes 1-2

Continued

Summary of Contents for IRB 1660















































































































































































































































































































































































































Search results

Summary of Contents for IRB 1660

Reviews:

Related manuals for IRB 1660

Brands by name

Popular brands

ABB IRB 1660, Product Manual

Search results

Summary of Contents for IRB 1660

Reviews:

Related manuals for IRB 1660

Brands by name

Popular brands