background image

2L-4153-00

Ó

Ò

Ò

TABLE TENNIS TABLE

MODEL NO.

T8780Q

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2013 Escalade  Sports

O W N E R ' S   M A N U A L

Please Do Not Return This Product To The Store!

Contact Escalade

®

 Sports customer service department at:

Phone:

1-866-873-3528

Toll – Free !

Fax:

1-866-873-3533

Toll – Free !

E-mail:

[email protected]

Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: 

www.escaladesports.com

ON-LINE TROUBLE SHOOTING

TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS

FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE

®

 

SPORTS PRODUCT INFORMATION

1. Read this manual carefully before starting assembly. 

Read each step completely before beginning 

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons 

before assembling or ordering parts.

 
5. Tools required for assembly:

 Phillips Screwdriver, Two 9/16  Wrenches, Two 7/16  Wrenches. 

Note: Adjustable wrenches can be substituted for wrenches.

6. Save this instruction manual and your proof of purchase (receipt) in the event that the 

manufacturer has to be contacted for replacement parts.

3. To make assembly easier, use the Hardware Identifier on page 2 to identify and sort all

fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. 

If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

Summary of Contents for Play The Best T8780Q











Reviews: