background image

CAUTION:

TO CLOSE:

1. Remove net and net posts from table.
2. Unlock all four hinges.
3. Lift one table half to midpoint until the
    plastic clips are engaged. Then continue
    lifting until closed.
4. Raise other table half in the same manner. 

as shown in Figure 10.

....

TO OPEN:

1. Hold center of top edge. Gently pull outward to midway position. 

Continue to pull until disengaged from plastic clips and legs rest on the
floor as shown in Figure 7A and 7B. Do not leave table partially 
opened at midway position.

2. Lower second top as described in step 1.
3. Lock all four center hinges. See Figure 8.
4. Attach net posts and net to table as shown in Figure 9.

NOTE: Net will be tight. It will be necessary to stretch net. This will insure
proper net tension.

....

 

....
....

PLAYING POSITION

IF TABLE IS NOT ALIGNING CORRECTLY: 

(see Figure 11)

1. Set the table to the Playing Position and lock hinges as shown in

Figure 8.

2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create

enough slack to align table tops. See Figure 1.

3. With the help of two other adults, push the two table top halves so 

they are in line with each other and re-tighten the Wing Nuts (#32) as 
shown in Figure 11.

OPENING AND CLOSING INSTRUCTIONS

Push to lock hinge.

Plastic

Clip

EXERCISE CAUTION IN OPENING/CLOSING TABLE.  SMALL CHILDREN, OR
CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE 
TABLE.  IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.  
DO NOT CLIMB, STAND, OR JUMP ON TABLE.  MOISTURE AND CONDENSATION WILL 
DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.

Midway
Position

PLAYBACK POSITION

Hinge 
Locked

To lock hinge push up on 
the table and push hinge 
as shown in Figure 7B.

STORAGE POSITION

TOP VIEW

Figure  11

Figure  10

Figure  9

Figure  8

Figure  7A

Figure  7B

Summary of Contents for Play The Best T8780Q











Reviews: