ABB IRB 1660 Product Manual Download

Page: 241 / 398

CAUTION

Always cut the paint with a knife and grind the paint edge when disassembling
parts. See

Cut the paint or surface on the robot before replacing parts on page 159

Removal, base

The procedure below details how to remove the base from the robot.

Note

Action

Decide which calibration routine to use, and
take actions accordingly prior to beginning the
repair procedure.

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the robot working
area.

CAUTION

Always cut the paint with a knife and grind the
paint edge when disassembling parts. See

Cut

the paint or surface on the robot before repla-
cing parts on page 159

The cable layout in the base is shown
in the figure

Illustration, cabling inside

base on page 169

Remove the cabling inside the base and pull it
up to the gearbox unit.

Detailed in section

Removing the

serial measurement unit on page 247

Remove the serial measurement unit.

Unfasten the base from the installation site by
removing the attachment bolts from the founda-
tion.

CAUTION

The robot weighs .
IRB 1600/IRB 1600ID: 250 kg
IRB 1660ID: 260 kg
All lifting accessories used must be sized ac-
cordingly!

Art. no. is specified in

Required

equipment on page 239

Fit the

lifting slings

to the robot, lift it and place

it with the side of the lower arm downwards on
a work bench.

Be careful not to damage the motor connectors!

Continues on next page

Product manual - IRB 1600/1660

241

3HAC026660-001 Revision: W

4 Repair

4.5.1 Replacement of base

Continued

Summary of Contents for IRB 1660















































































































































































































































































































































































































Search results

Summary of Contents for IRB 1660

Reviews:

Related manuals for IRB 1660

Brands by name

Popular brands

ABB IRB 1660, Product Manual

Search results

Summary of Contents for IRB 1660

Reviews:

Related manuals for IRB 1660

Brands by name

Popular brands