manualshive.com logo in svg

ABB ACS880-04F, Hardware Manual, Page: 8 / 172

Share
Download
ABB ACS880-04F Hardware Manual Download Page 8

8   

Drive  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78
Input cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   78
Motor and motor cable   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   78
Brake resistor and resistor cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   78

Checking the compatibility with IT (ungrounded) systems . . . . . . . . . . . . . . . . . . . . . . .   79

Grounding the drive module  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   80

Connecting the power cables   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   80

Power cable connection diagram   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81
Power cable connection procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   82
DC connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83

Overview of control cable connection process   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83
Removing the control panel holder from the external control unit  . . . . . . . . . . . . . . . . .   84
Attaching the control cable clamp plate  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   85
Connecting the external control unit to the drive module . . . . . . . . . . . . . . . . . . . . . . . .   86

Routing the control unit cables into the drive module  . . . . . . . . . . . . . . . . . . . . . . . .   86
Connections to the drive module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   86
Connections to the control unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   87

Connecting the control cables to the terminals of the control unit  . . . . . . . . . . . . . . . . .   88

Default I/O connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   89

Notes:  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   90
External power supply for the control unit   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   90
AI1 and AI2 as Pt100, Pt1000, PTC and KTY84 sensor inputs (XAI, XAO) . . . . .   91
DI6 (XDI:6) as PTC sensor input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92
DIIL input (XD24:1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92
Drive-to-drive link (XD2D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   92
Safe torque off (XSTO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93
Safety functions (X12)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93

Installing the control panel holder back onto the external control unit   . . . . . . . . . . .   93

Connecting a control panel   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94
Controlling several drives from one control panel through panel bus  . . . . . . . . . . . . . .   94
Connecting a PC  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   95
Installing optional modules   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   95

Installing the FSO safety functions module (oQ972 and +Q973)  . . . . . . . . .   95
Installing I/O extension, fieldbus adapter and pulse encoder interface modules   . . .   97

Wiring the optional modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   97

Connecting the memory unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   98

8. Installation checklist

Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   99
Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   99

9. Start-up

Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103
Start-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103

10. Fault tracing

Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105
LEDs with oJ410  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105
Warning and fault messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105

Summary of Contents for ACS880-04F













































































































































































Reviews:

No comments