manualshive.com logo in svg

ABB ACS880-04F, Hardware Manual, Page: 47 / 172

Share
Download
ABB ACS880-04F Hardware Manual Download Page 47

Mechanical installation   47

5

Mechanical installation

Contents of this chapter

This chapter describes how to install the drive module mechanically without the clear 
plastic shrouds. The shrouds are attached after the power cabling.

Examining the installation site

Examine the installation site:

•

The installation site is sufficiently ventilated or cooled to transfer away the drive 
losses. 

1) 

•

The ambient conditions of the drive meet the specifications. 

1)

•

The material onto which the drive module is mounted must be non-flammable and 
strong enough to carry the weight of the module.

•

There is enough free space above the drive to enable cooling air flow, service and 
maintenance.

•

The floor that the drive is installed on is of non-flammable material, as smooth as 
possible, and strong enough to support the weight of the drive.

1) 

See section 

Ambient conditions

 on page 

132

 for the allowed ambient conditions and 

section 

Losses, cooling data and noise

 on page 

127

 for the required cooling air.

Summary of Contents for ACS880-04F













































































































































































Reviews:

No comments