ABB ACS880-04F Hardware Manual Download Page 97

Page: 97 / 172

Electrical installation 97



Installing I/O extension, fieldbus adapter and pulse encoder
interface modules

See page

for the available slots for each module.

WARNING!

Obey the safety instructions in chapter

Safety instructions

. If you

ignore them, injury or death, or damage to the equipment can occur.

1. Stop the drive and do the steps in section

Precautions before electrical work

on page

before you start work.

2. Insert the module carefully into its position on the control unit.

3. Tighten the grounding screw torque of 0.8 N·m.

Note:

The screw tightens the

connections and grounds the module. It is essential for fulfilling the EMC requirements
and for proper operation of the module.

Wiring the optional modules

See the appropriate optional module manual for specific installation and wiring
instructions.

Summary of Contents for ACS880-04F













































































































































































Search results

Summary of Contents for ACS880-04F

Reviews:

ABB ACS880-04F, Hardware Manual, Page: 97 / 172

Search results

Summary of Contents for ACS880-04F

Reviews: