ABB ACS880-04F Hardware Manual Download Page 99

Page: 99 / 172

Installation checklist 99

Installation checklist

Contents of this chapter

This chapter contains a list for checking the mechanical and electrical installation of the
drive module.

Installation checklist

Go through the checklist below together with another person.

WARNING!

Obey the safety instructions in chapter

Safety instructions

. If

you ignore them, injury or death, or damage to the equipment can occur.

Check that …

Cabinet construction

The drive module is fastened properly to the cabinet. (See chapters

Guidelines for planning the

mechanical installation

)

Mechanical joints are tightened and not broken.

Parts are clean and painted surfaces not scratched.
The cabinet frame and parts which are in metal to metal contact with the frame (for example seams,
component fixing points on assembly plates, back of control unit mounting plate) are

not

finished

with non-conducting paint or material.

Degree of protection (IPxx)

Summary of Contents for ACS880-04F













































































































































































Search results

Summary of Contents for ACS880-04F

Reviews:

ABB ACS880-04F, Hardware Manual, Page: 99 / 172

Search results

Summary of Contents for ACS880-04F

Reviews: