background image

Third-Party Copyright Compliance

 

Copyright-5

41-001343-02 REV05 – 07.2014

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED 
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE 
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTER-
RUPTION).

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGE.

Wind River Systems - VxWorks software

The VxWorks Run-Time software module is Copyright (c) WindRiver Systems Inc, all rights reserved. It is licensed for use, 
not sold. All use of this product and the VxWorks Run-Time module is subject to agreement with the following EULA 
terms 

With respect to the Run-Time Module, Wind River and its licensors are third party beneficiaries of the End User License 
Agreement and that the provisions related to the Run-Time Module are made expressly for the benefit of, and are 
enforceable by, Wind River and its licensors. 

Activities expressly prohibited: (i) copying the Run-Time Module, except for archive purposes consistent with the End 
User’s archive procedures; (ii) transferring the Run-Time Module to a third party apart from the Target Application; (iii) 
modifying, decompiling, disassembling, reverse engineering or otherwise attempting to derive the Source Code of the 
Run-Time Module; (iv) exporting the Run-Time Module or underlying technology in contravention of applicable U.S. and 
foreign export laws and regulations; and (v) using the Run-Time Module other than in connection with operation of the 
Target Application. 

Aastra and Wind River Systems: (i) Retain ownership of all copies of the Run-Time Module; (ii) expressly disclaim all 
implied warranties, including without limitation the implied warranties of merchantability, fitness for a particular pur-
pose, title and non-infringement; (iii) exclude liability for any special, indirect, punitive, incidental and consequential 
damages; and (iv) require that any further distribution of the Run-Time Module be subject to the same restrictions set 
forth herein.

UPnP - Intel

INTEL SOFTWARE LICENSE AGREEMENT (Final, Site License)

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING. 

Do not use or load this software and any associated materials (collectively, the "Software") until you have carefully read 
the following terms and conditions. By loading or using the Software, you agree to the terms of this Agreement. If you do 
not wish to so agree, do not install or use the Software.

LICENSE. You may copy the Software onto your organization's computers for your organization's  use, and you may make 
a reasonable number of back-up copies of the Software, subject to these conditions: 

1. You may not copy, modify, rent, sell, distribute or transfer any part of the Software except as provided in this Agree-
ment, and you agree to prevent unauthorized copying of the Software.

2. You may not reverse engineer, decompile, or disassemble the Software. 

3. You may not sublicense the Software. 

4. The Software may include portions offered on terms in addition to those set out here, as set out in a license accompa-
nying those portions. 

Summary of Contents for 6737i

























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: