manualshive.com logo in svg

Aastra 6737i, Administrator'S Manual

The Aastra 6737i is a feature-rich VoIP phone offering exceptional audio quality and advanced communication capabilities. Unlock its full potential by downloading the free Quick Reference Manual from manualshive.com, providing step-by-step instructions for easy setup and efficient usage of this impressive device.

Share
Download
background image

Operational Features

 

5-77

41-001343-02 REV05 – 07.2014

Call Forward Mode

Call Forward (CFWD) on the IP phone allows incoming calls to be forwarded to another destination. The phone sends the 
SIP message to the SIP proxy, which then forwards the call to the assigned destination.

An Administrator or User can configure CFWD on the phone-side by setting a mode for the phone to use (

Account

, 

Phone

, or 

Custom

). Once the mode is set, you can use the IP Phone UI to use the CFWD feature at 

Options->Call Forward

 

or by pressing a configured Call Forward softkey/programmable key/extension module key.

The following describes the behavior for each CFWD mode.

•

Account mode 

- The account mode allows you to configure CFWD on a per account basis. Pressing a configured 

CFWD key applies to the account in focus.

•

Phone mode 

- The Phone mode allows you to set the same CFWD configuration for all accounts (

All

, 

Busy

, and/or 

No 

Answer

). When you configure the initial account, the phone applies the configuration to all other accounts. (In the 

Aastra Web UI, only the account you configured is enabled. All other accounts are grayed out but set to the same con-
figuration.) Using the Aastra Web UI, if you make changes to that initial account, the changes apply to all accounts on 
the phone.

•

Custom mode 

- The Custom mode allows you to configure CFWD for a specific account or all accounts. You can con-

figure a specific mode (

All

, 

Busy

, and/or 

No Answer

) for each account independently or all accounts. On the 3-line 

LCD phones and the 6867i, you can set all accounts to 

ALL On

 or 

ALL Off

. On the 8 and 11-Line LCD phones and the 

6739i, you can set all accounts to 

All On

, 

All Off

, or copy the configuration for the account in focus to all other 

accounts using a 

CopytoAll

 softkey.

The states you can set for Call Forward are 

All

, 

Busy

, 

No Answer

. You can enable different call forwarding rules/modes 

independently (for example, you can set different phone numbers for Busy, All, and NoAns modes and then turn them 
on/off individually. The behavior of these states is dependent on the mode (account, phone, or custom) you configure on 
the phone.

Reference

For more information about how Call Forwarding works and how you can use it on the IP Phones, see 

“Call Forwarding”

 

on 

page 5-197

.

Configuring Call Forward Key Mode

Use the following procedures to set the Call Forward key mode on the IP phones.

Note:

If there is only one account configured on the phone, then the mode setting is ignored and the phone behaves as if the 
mode was set to “Phone”.

Configuration Files

For specific parameters you can set in the configuration files, see Appendix A, the section, 

“Call Forward Key Mode Settings”

 on 

page A-111.

Summary of Contents for 6737i

























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6737i

Xqisit BH100 Manual preview
BH100
Brand: Xqisit Pages: 16
Turtle Beach Black Ops II Sierra User Manual preview
Black Ops II Sierra
Brand: Turtle Beach Pages: 27
Avaya Headset CAT132 MX User Manual preview
Headset CAT132 MX
Brand: Avaya Pages: 4
ACME BH20 User Manual preview
BH20
Brand: ACME Pages: 96
Porta Phone The EPAK Quick Start Manual preview
The EPAK
Brand: Porta Phone Pages: 2
Maxell Hypershock CA-BTVH User Manual preview
Hypershock CA-BTVH
Brand: Maxell Pages: 29
Harman AKG K830 BT User Manual preview
AKG K830 BT
Brand: Harman Pages: 8
Jabra UC VOICE Datasheet preview
UC VOICE
Brand: Jabra Pages: 2
Jabra MOTION UC Datasheet preview
MOTION UC
Brand: Jabra Pages: 2
Jabra PRO 9465 DUO Quick Start Manual preview
PRO 9465 DUO
Brand: Jabra Pages: 4
Jabra GN2000 OC Series Datasheet preview
GN2000 OC Series
Brand: Jabra Pages: 2
Jabra GN9350e Quick Start Manual preview
GN9350e
Brand: Jabra Pages: 3
Jabra Talk 25 User Manual preview
Talk 25
Brand: Jabra Pages: 14
Jabra SUPREME User Manual preview
SUPREME
Brand: Jabra Pages: 19
Jabra DRIVE Technical Specifications preview
DRIVE
Brand: Jabra Pages: 1
Jabra 9465 Datasheet preview
9465
Brand: Jabra Pages: 2
Jabra GO 6430 Quick Start Manual preview
GO 6430
Brand: Jabra Pages: 27
Jabra BT4010 Quick Start Manual preview
BT4010
Brand: Jabra Pages: 2

Brands by name

Popular brands

Load more brands