3Com LS8M1P12TEH Installation Manual Download Page 250

Page: 250 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Appendix B N68 Cabinet Installation

B-52

(1) Cabinet

(2) Antistatic floor

Figure B-50

Cabinets installed on the raised antistatic floor

B.3.10 Verifying Installation

The following requirements must be satisfied:

The positions of the cabinets must comply with the construction design.

All the bolts used to fix support and cabinets should be installed stably. Spring

washers and flat washers should be installed correctly.

The insulation accessories between supports and cabinets must satisfy the

insulation requirements. Self-made bases are recommended to be insulated from

the ground or the cabinets.

The entire row of cabinets should be arranged closely and neatly. The vertical

deviation should be less than 3 mm (0.1 in.)

The cabinet doors at the primary walkway side should be in a straight line. The

error must be less than 5 mm (0.2 in.).

The surface of the entire row of cabinets should be on the same plane. Adjacent

cabinets should be closely arranged.

All the bolts should be fastened with spring washers and flat washers.

Make sure that no component is deformed.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands