3Com LS8M1P12TEH Installation Manual Download Page 127

Page: 127 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 6 Hardware Maintenance

6-5

Fan trays of the S7503, S7506, and S7506R are fixed in different ways. The fan trays of

the S7506R and the S7503 are fixed by captive screws, while the fan tray of the S7506

is fixed by two locks.

The following describes how to install and remove these two types of fan trays,

respectively.

6.4.1 Replacing the Fan Tray of the S7506

I. Removing the fan tray

Figure 6-3

Removing the fan tray from the S7506

Follow these steps to remove the fan tray from the S7506:

Wear the ESD-preventive wrist strap and push down the locks on the two ejector

levers of the fan tray. Meanwhile, pull the two ejector levers outward to separate

the fan tray from the backplane. See Figure 6-3.

Caution:

If you want to replace the fan tray when the switch is working, separate the fan tray

from the backplane to disconnect the power and wait till the fan stops rotating before

pulling it out completely. Considering that the fan may be still rotating, avoid

stretching your hands into the fan tray.

Push down the locks before pulling the ejector levers outward. Otherwise, the locks

may be broken.

Grasp the two ejector levers and slide the fan tray out of the slot. See Figure 6-3.

Put the fan tray into the package.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands