3Com LS8M1P12TEH Installation Manual Download Page 201

Page: 201 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Appendix B N68 Cabinet Installation

B-3

B.1.3 Installation Preparation

Follow the given steps to do the installation preparation:

Draw lines correctly to avoid rework.

Unpack the cabinet and the cabinet accessories according to the operation guide.

Caution:

If you need to install feet for the cabinet on cement floor, refer to Installing Cabinet

Accessories”. Then proceed with step 3.

After installing feet, you must fix the cabinets to avoid accidents.

You can use supports to install cabinets on antistatic floor. You do not need to install

feet.

Note:

The way of fixing the cabinet with feet is not recommended.

3) Put the rack in the upright position, and then remove wood boards and support

wood bars from the back with a cross-head screwdriver. Put the removed boards

and bars in a safe place to avoid injury. Keep the removed screws for later use.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands