3Com LS8M1P12TEH Installation Manual Download Page 147

Page: 147 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 7 Software Maintenance

7-12

2. Set FTP protocol parameter

3. Set XMODEM protocol parameter

0. Return to boot menu

Enter your choice(0-3):3

You can select different protocols to load the host software.

The subsequent steps are the same as those for loading a Boot ROM, except for the

prompt information.

7.3 Loading Software Through Command Lines

7.3.1 Loading Using FTP

Run the FTP Server on a local PC. Ensure that you have configured the username and

password and set the correct file directory. Assume that the IP address of the PC is

10.10.110.1.

switch by using FTP.

Note:

The S7500 series support dual image booting. That is, the S7500 series normally

boot with the main image (i.e. the primary file), but with the backup image (i.e. the

backup file) when errors occur to the primary one. Refer to section 7.5 “Booting the

Switch with Dual Images” on page 7-17 for details.

The S7500 series also support the upgrade by using host software containing the

Boot ROM file. That is, you can upgrade the Boot ROM of all boards using such host

softwware. Refer to section 7.6 “Loading Host Software Containing the Boot ROM

File” on page 7-19 for details.

Assume that:

The main boot file is SWITCH002.app.

The host software running on the switch is SWITCH001.app.

The Boot ROM program is SWITCHbtm.btm.

Follow these steps after logging in to the switch.

Download the software to the switch using FTP.

<H3C> ftp 10.10.110.1

Trying ...

Press CTRL+K to abort

Connected.

220 WFTPD 2.0 service (by Texas Imperial Software) ready for new user

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands