3Com LS8M1P12TEH Installation Manual Download Page 136

Page: 136 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 7 Software Maintenance

7-1

Chapter 7 Software Maintenance

You can use command lines or the BOOT menu to load software of the S7500 series.

7.1 Introduction to Loading Approaches

7.1.1 Loading Software Through the Boot Menu

You can load the software:

From the console port using XModem

From an Ethernet port using TFTP

From an Ethernet port using FTP

Note:

The Boot ROM version must match the host software version when you load a Boot

ROM and host software. You are recommended to upgrade the Boot ROM only

when the host software to be loaded does not match the existing Boot ROM version.

Frequent Boot ROM loading is discouraged.

You can use the Boot Menu to load a Boot ROM and host software of only SRPUs.

To load a Boot ROM of LPUs, you must use command lines.

7.1.2 Loading Software through Command Lines

You can load software through command lines using:

FTP

TFTP

7.2 Loading Software Through the Boot Menu

If your terminal is directly connected to the switch, you can load a Boot ROM and host

software of SRPUs.

Before loading, make sure that your terminal is correctly connected to the switch.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands