3Com LS8M1P12TEH Installation Manual Download Page 12

Page: 12 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 1 Product Overview

1-6

(1)

(2)

(3)

(5) (6)

(7) (8) (9)

(14)

(12)

(4)

(10)

(13)

(15)

(11)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(1) SFP port number

(2) SFP port (Gigabit)

(3) Console port

(4) Management Ethernet port

(5) LINK LED of the management Ethernet
port

(6) ACT LED of the management Ethernet
port

(7) RUN LED of LPU

(8) ALM LED of LPU

(9) RUN LED of SRPU

(10) ALM LED of SRPU

(11) Silkscreen

(12) Captive screw

(13) SRPU edge (pink)

(14) RESET button

(15) Ejector lever

(16) OK LED of the power

(17) FAIL LED of the power

(18) OK LED of the fan

(19) FAIL LED of the fan

(20) SFP port status LED

(21) CF card port

(22) Button for ejecting the CF card

Figure 1-5

Panel of a Salience III Series SRPU (LS81SRPG)

Note:

The panel of a Salience III Edge SRPU is the same as that of a Salience III SRPU

except the board name and board silk-screen.

The panel of a Salience III Plus SRPU is the same as that of a Salience III SRPU

except that it has a different board name and board silk-screen and provides no SFP

port.

1.3.4 Ports

I. CF card port

The port supports standard CF cards. The CF card stores the host version to facilitate

the online software upgrade.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands