3Com LS8M1P12TEH Installation Manual Download Page 90

Page: 90 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 3 Installation Preparations

3-1

Chapter 3 Installation Preparations

3.1 Safety Precautions

To avoid bodily injury and device damage, please read the following safety

recommendations carefully before installing the S7500 series. The recommendations

do not cover every possible hazardous condition.

3.1.1 General Safety Recommendations

Keep the chassis clean and dust-free.

Keep the chassis and installation tools away from walk areas.

Do not wear loose clothing, jewelry (including ring and necklace, and so on), or

any other things that could get caught in the chassis when you install or maintain

the switch.

3.1.2 Electrical Safety

Look carefully for possible hazards in your work area, such as ungrounded power

extension cables, missing safety grounds, and moist floors.

Locate the emergency power switch in the room before installation so that you can

shut the power off at once in case of an electrical accident.

Unplug all external cables before moving the chassis.

Avoid maintaining the equipment alone when it is powered by electricity.

Never assume that power is disconnected from a circuit. Always check.

Do not place the switch on a moist area or let liquid flow into it.

3.1.3 Handling Safety

Since the S7500 series are rather large and heavy, you should follow the

recommendations below.

Disconnect all power and all external cables (including power cables) before

carrying or moving the chassis.

Ask somebody to move the switch together.

Move the switch slowly and stably.

Keep in step with your partner and balance your bodies when moving the switch.

Summary of Contents for LS8M1P12TEH


































































































































































































































































































Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands

3Com LS8M1P12TEH, Installation Manual

Search results

Summary of Contents for LS8M1P12TEH

Reviews:

Related manuals for LS8M1P12TEH

Brands by name

Popular brands