Zontes ZT125-Z2 Скачать руководство пользователя страница 71

Страница: 71 / 76

11-REAR COVER COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1174100-002000 ZT250

－

S rear reflector

1221200-051000 KD150

－

U rear fender plate

1244100-006000 ZT250

－

S rear liceness rubber buffer

1181200-103000 KD150

－

U auxiliary mud plate transfer line

（

short

）

1171200-057000 KD150

－

U license plate light

1251300-063093 Plywood M6×11×15(color zinc)

1170300-064000 HJ125

－

K front right turn signal light

1221200-053000 KD150

－

U rear turn signal bracket

1170300-063000 HJ125

－

K front left turn signal light

Fig.5 REAR COVER

COMPONENT

Rear mud board component 2

PROCEDURE:

●

Rear fender

Remove the nuts and washers that come with the rear reflector (1) and then remove the reflector. Remove the
license plate buffer glue

⑶

from the rear fender

⑵

●

Turn signal light assembly

Unplug all the connectors of the turn signal and the license plate light and remove the auxiliary fender adapter
cable

⑷

Remove the 2 pieces of nuts

⑹

from the turn signal bracket

⑻

Remove the 3 screws that come with the license plate light, and then remove the license plate light

⑸

Grasp the left (right) turn signal and use a 17# open-end wrench to remove the nut that comes with the turn

signal, remove the spring washer and gasket that comes with it, and then remove the turn signal.

CAUTION:

●

Do not pull the cable hard when removing the sub-mud switch.

●

When reassembling, check if there is any pressure on the wire to prevent it from tightening.Short circuit

caused by bolts. Pay attention to the lamp connector, do not insert the wrong, turn left

Green + orange; right turn signal is green + blue; license plate light is green + pink.

●

When assembling self-tapping screws come with the license plate light, it must be perpendicular to mounting

surface, otherwise it will bedamaged,and the torque should not be too large.

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды