Zontes ZT125-Z2 Скачать руководство пользователя страница 47

Страница: 47 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-101000 Non-standard bolt M6×12

（

304 stainless steel

）

1224100-037000 grade 0 flame retardant tie (black 3.6×295)

Fig.10 FRONT FORK

COMPONENT

PROCEDURE:

●

Remove the headlight

Turn the stearing to the far left, and remove the 2 bolts (1) in Figure A.
Turn the stearing to the far right, and remove the 2 bolts (1) in Figure
B. Use scissors to cut off the tie

⑵

in Figure C.

Unplug all the plugs in Figure D and remove the headlights.

CAUTION:

●

Pay attention to the force when removing the cable and unplugging the plug and the cable to avoid damage.

●

The head unit should be supported during the disassembly process and protective measures should be taken

toprevent scratching the lamp cover or paint surface.

Head and headlights component 1

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды