Zontes ZT125-Z2 Скачать руководство пользователя страница 21

Страница: 21 / 76

4-REAR WHELL COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-105000 ZT310

－

Z chain adjuster bolt M10×70

1251300-050000 ZT310

－

Z chain adjuster bolt M10(304 stainless steel)

ZT310 R, chain adjuster

1251300-067000 ZT250

－

R rear wheel hollow shaft nut

110N.m

ZT310 L, chain adjuster

1091200-025000 KD150

－

U rear wheel hollow shaft

1274200-002000 ZT310 rear wheel right sleeve φ20×φ28×φ38×18.5

1244200-050000 ZT310

－

T cushion gum

1094200-011000 ZT310

－

R sprocket

Sprocket

1251300-057093 Non

－

standard nut M10×1.5(dacromet)

45±3N.m

1094100-035000 ZT310 rear wheel left sleeve φ20×φ30×φ35×17.8

Fig.3 REAR WHELL

COMPONENT

Rear wheel component 1

PROCEDURE:

●

Rear wheel assembly

Disassemble rear wheel axle nut

⑷

with a 30# sleeve.

Using 17# open spanner to move chain adjuster nut

⑵

on both sides towards rear wheel axle until they reach

chain adjusting bolt

⑴

. Then rotate the bolts

⑴

and nuts

⑵

towards motorcycle front direction till the end.

Push rear wheel assembly towards motorcycle front direction and take off the chain from sprocket.
Hold the rear wheel assembly. Punch rear wheel axle

⑹

with rubber hammer. Take off right chain adjuster

⑶

right axle sleeve

⑺

, rear tire and rim assembly, left axle sleeve

⑿

, left chain adjuster

⑸

. Tie firmly the rear disc

brake clamp and avoid it to be lifed higher than disc brake oil cup. Disassemble the rear wheel axle at last.

●

Sprocket bracket assembly

Put down the rear wheel assemble horizontally. Take off nut

⑾

with 14# sleeve. Take off sprocket

⑽

; sprocket

bracket

⑼

. Pull out the sprocket gum cushion

⑻

from the rim.

CAUTION:

●

Use suitable tool to support the motorcycle. Avoid accidents caused by falling motorcycle. Single person

manipulation is prohibited.All the standard parts need to reach standard torque while reassembling.

●

Using iron hammer to punch rear wheel axle, disc brake clamp assembly is prohibitd.

●

While disassembling the rear wheel assemble, avoid the rear disc brake clamp to be lifted higher than the disc

brake oil cup. If not, air will get into the tubes and cause softness or failure on braking system. As disc brake

tubes request extreamly high vaccum degree. Make sure manipulator has maintenance ability before

disassembling the disc brake assembly.

●

Check the chain regularly. Increase the frequency of adjustment of the chain according to the driving

conditions. Keep the tightness of chain to be in a suitable range. Too loose chain have possibility to separate from

sprocket or damage the engine. Too tight chain can be worn out quickly.

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды