Zontes ZT125-Z2 Скачать руководство пользователя страница 51

Страница: 51 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1194100-001000 ZT250

－

S left rearview mirror

1251100-121093 Non-standard bolt M8×25 (color zinc)

1134100-017000 ZT250

－

R half cover of left handle bar

1184200-184000 ZT310-V1 left handlebar switch

1244100-041000 ZT250-R left hand rubber sleeve

1134200-023000 ZT250

－

R balance block assembly

1134200-010000 ZT310

－

VLeft hand rocker arm (CNC)

1244200-046000 ZT310-V clutch line sheath

1134200-011000 ZT310-V left hand rocker arm assembly

1251300-073000 GB/T6185 hexagonal nylon lock nut M6

1251100-198000 Non-standard hexagon socket bolt M6×13-φ8×20

1184100-107000 ZT250-R clutch switch

PROCEDURE:

●

Left rear view mirror, left switch, rocker arm

Remove the clutch line by referring to the “Replace Clutch Line” procedure. Remove the left rear view mirror

⑴

left switch

⑷

by referring to the steps in "Right Handle Assembly" and "Add Brake Fluid, Adjusting Rocker

Arm".

Using 6# inner hexagon socket remover 2pcs bolts

⑵

take off the half cover

⑶

and the left hand arm assembly.

●

Left hand rubber sleeve and balance block assembly

Use a blow gun to blow the left hand grip

①

between the rubber sleeve

⑸

and the direction handle tube while

moving the rubber sleeve inward until the balance block positioning hole is exposed.

Use the tool to press the convex part at both ends of the elastic piece on the balance block and pull out the

balance block assembly

⑹

Use a blow gun to blow the left hand grip

⑸

and the direction between the tubes, and move the outer sleeve to

remove the left hand grip

⑸

●

Replace the left hand rocker arm and clutch switch

Take off the rubber sleeve

⑻

.Then fix the bolt

⑾

with a 5# inner hexagon socket then remove the nut

⑽

Remove the bolt

⑾

and remove the left-hand rocker arm

⑺

and the rocker arm assembly

⑼

Rotate the adjusting nut

②

to adjust the distance between the rocker arm and the left handle to adjust the rubber

sleeve to adapt to different driver's hand feeling.

First remove the clutch switch plug, then use a cross screwdriver to remove the bolt

③

, remove the clutch switch

⑿

CAUTION:

●

The vehicle should be fixed before operation

●

The disassembly and assembly of the clutch line is carried out according to the step of adjusting the

clutch cable.

●

Note the triangle symbol on the rocker arm assembly and the half cover seam alignment switch.

Fig.14 FRONT FORK

COMPONENT

Left hand component

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды