Zontes ZT125-Z2 Скачать руководство пользователя страница 59

Страница: 59 / 76

8-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1250205-023000 GB70.1 inner hexagonal M8X35 (army green)

1244100-023000 ZT250

－

S fixed cushion block

1244100-020000 ZT250

－

S tank pressure glue

1244100-053000 ZT250-S fuel tank gasket

1224100-037000 Grade 0 flame retardant tie (black 3.6×295)

Fig.1 FUEL TANK

COMPONENT

Fuel tank component

PROCEDURE:

●

Fuel tank component

Use the key to unlock the cushion lock and remove the cushion. Follow the steps for removing the side cover to

remove the left and right side covers.

Use scissors to cut off the cable ties (5) that bind the turn signal and USB interface on the left and right guard

bars, and unplug the turn signal and USB interface by the way.

Use 6# inner hexagon to remove 2 bolts

⑴

, take off the cushion fixing block

⑵

, and remove the rubber

⑶

Rubber pad

⑷

does not need to be removed if it does not need to be replaced.

One person lifts the rear part of the fuel tank slightly, and one person unplugs the high-pressure fuel pipe plug

①

and the fuel pump plug

②

on the right side of the bike. Notice that the buckle of the fuel pump plug is on

the inside and cannot be removed forcibly. Unplug the fuel pipe

③

connected to the dump valve of the carbon

canister on the left side of the bike.

Grab the head of the fuel tank assembly with one hand and pull it back, and with the other hand, grab the

rear part and lift it up and shake it left and right. Remove the fuel tank assembly from the bike and place it.

CAUTION:

●

The parts should be protected during the disassembly process to prevent damage to the paint surface.

●

When removing the buckle, pay attention to the strength to prevent damage to the buckle.

●

When removing the high-pressure oil pipe, be sure to wait until the engine and muffler are completely

cooledbefore operating to prevent accidental ignition of the fuel and cause fire.

●

Fireworks, answering or dialing should be strictly prohibited near the car-breaking site to prevent accidents.

●

A small amount of fuel leakage is required when the high-pressure oil pipe sub-assembly is pulled out, andthe

fuel should be prevented from dripping to the outside of the engine or the muffler.

●

It is recommended to use the oil pump to pump out the fuel or consume the fuel before disassembling the

tankassembly.

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Бренды по названию

Популярные бренды