Zontes ZT125-Z2 Скачать руководство пользователя страница 42

Страница: 42 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1194100-002000 ZT250

－

S right rearview mirror

1134100-032000 ZT250-R Right handle rocker (Machine)

1134200-023000 ZT250

－

R balance block assembly

1244100-042000 ZT250

－

R right handle bar rubber sleeve

1134100-019000 ZT250-R right hand half cover

1251100-121093 Non-standard bolt M8×25 (color zinc)

Fig.5 FRONT FORK

COMPONENT

Right hand component

PROCEDURE:

●

Rearview mirror

Hold the mirror stem in one hand, remove the nut

④

with a sleeve, and remove the small pad

③

, the spring

②

and the large pad

①

. Remove the mirror from the front brake master pump.

●

Right handlebar to put rubber sleeve, balance block

Push the rubber sleeve

⑸

with the right handlebar to push forward to expose the upper balance block fixing

hole; use the tool to press the convex parts at both ends of the elastic block on the balance block and pull out the
balance block assembly

⑷

, and then put the right handle Remove the rubber sleeve

⑸

●

Right handlebar half cover

Hold the front disc brake main pump

⑵

with one hand, and remove the bolt

⑺

with a 6# inner hexagon socket.

remove the half cover of right handle bar

⑹

CAUTION:

●

The motorcycle should be fixed after horizontal support.

●

Periodically check that the fluid level of the brake fluid is between 3/4 of the observation window.

●

Do not flush the cup directly with high pressure water.

●

The small spacer of the rear view mirror anti-rotation limit slot needs to be aligned with the slot on the mirror

bar bolt.

●

The right handlebar refers to the switch to replace the throttle line.

●

The joint between the front disc brake main pump and the half cover should be aligned with the right hand to

match the triangle on the switch.

ZT125T front disc main pump assembly

（

without

rocker arm

）

1100300-044000

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды