Zontes ZT125-Z2 Скачать руководство пользователя страница 45

Страница: 45 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1250205-023000 GB70.1 inner hexagonal M8X35 (environmental color)

20N.m

1094100-033000 ZT250

－

R front wheel hollow shaft

1094100-008000 ZT250

－

R front right sleeve

1100100-601000 KD150

－

U front brake disc plate(300 × 4.5 / KD)

1251100-117093 Non

－

standard inner hex bolt M8×25(color zinc)

～

24N.m

1274200-058000 ABS induction ring (60 teeth)

1094100-036000 ZT250

－

R front wheel right shaft sleeve

1094100-037000 ZT250

－

R front wheel right fixed bushing

1091200-032000 KD150

－

U bright black front rim (3.0 × 17)

1230200-006000 HJ100

－

D tire valve cap

1230100-047000 Environmental vacuum tyre valve spile(TR

－

412)

PROCEDURE:

●

Tire and wheel component

Remove the 2 bolts

⑴

on the left front shock absorber bottom "b" with a 6# inner hexagon socket. Hold

the front wheel firstand then remove the hollow shaft

⑵

with a 17# inner hexagon socket, remove the left

sleeve

⑶

, and move thefront wheel component downward to remove the right sleeve

⑺

and front wheel

component. Finally, use thehexagonal tool to remove the 2 bolts

⑴

of the right front shock absorber "a",

remove the right fixing sleeve

⑻

●

Brake disc, ABS ring gear

Using 6# inner hexagon socket remove 5pcs bolts

⑸

,then take off the ABS ring gear

⑹

and the disc

⑷

●

Tire and rim component

Disassemble tire valve cap

⑾

. Deflate the tire with tools. Then disassemble the rear tire

⑼

with

professional tire changing machine. Disassemble the tire valve

⑿

with suitable tool.

CAUTION:

●

Use a suitable tool to support the motorcycle to prevent accidents caused by dumping during disassembly.

●

Take care when disassembling tires and rims to prevent damage to the material.

●

After replacing the tire, check for leaks and balance.

●

Unqualified tire repair fluid may corrode rims and cause safety hazards.

●

Insufficient tire pressure may cause steering vibration, abnormal wear, etc.; summer tire pressure is too high

there is a risk of puncture.

●

Maintenance items

Tires: The tires should be regularly inspected for cracks, cracks, air pressure, etc. If the tread wear indicator has

been worn out, the tire of the same specification type must be replaced. Refer to the relevant content of the

manual for details.

Rim: Check the rim for any deformation, cracks, etc. Rotate the rim horizontally to check for sticking,swinging,

etc.Rim seal φ42 × φ28 × 7; bearing model: 6004-2RS.

Axle: Use a dial indicator to check for deformation and bending.

Brake disc: After replacing the brake disc, the new brake disc should be operated for about 300 kilometers to

fully run in order to achieve the best braking effect. Be careful to leave enough braking distance during running-

in.

1230100-445000 110/70-17 (CMNK01) environmental protection

vacuum tire

Front wheel component

Fig.8 FRONT FORK

COMPONENT

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды