Zontes ZT125-Z2 Скачать руководство пользователя страница 62

Страница: 62 / 76

8-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251300-063093 Plywood M6×11×15

（

color zinc

）

4041201-155051 KD150-Z2 dark gray front right cover (high light)

4041201-154051 KD150-Z2 dark gray front left side cover (high light)

1224100-008000 ZT250

－

S snap joint

1251100-101000 Non-standard bolt M6×12 (304 stainless steel)

1244100-052000 Buffer rubber of flanging bushing

（

φ8.5×φ14×1

）

1274100-057095 Flanging bushing φ6.2×φ8.5×3.5

＋

φ14×1.5

1220300-150000 SK150-Z fuel tank right bottom plate

1220300-149000 SK150-Z fuel tank left bottom plate

PROCEDURE:

●

Side cover front assembly

Take the front part of the left side cover

⑶

and the front part of the right side cover

⑵

out in the direction of

the arrow, and remove the 2 splints

⑴

and 4 buckles

⑷

Remove the 4 bolts

⑸

fixing the left bottom plate

⑼

and the right bottom plate

⑻

with a 4# inner hexagon,

and remove the bushing

⑺

and cushion rubber

⑹

CAUTION:

●

The parts should be protected during the disassembly process to prevent damage to the paint surface.

●

When removing the buckle, pay attention to the strength to prevent damage to the buckle.

Fig.4 FUEL TANK

COMPONENT

Fuel tank cover component 3

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды