Zontes ZT125-Z2 Скачать руководство пользователя страница 52

Страница: 52 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1224100-025000 ZT250

－

S M8 bolt decorative buckle

1250205-023000 GB70.1 inner hexagonal M8X35 (environmental color)

1134200-005000 ZT310

－

R press block of handle bar(home

－

made)

1134200-003000 ZT310

－

R handle bar

Directional lever component

Fig.15 FRONT FORK

COMPONENT

PROCEDURE:

●

Directional components

Using a blade to pick up the decorative buckles

⑴

, hold the direction handle

⑷

in one hand, and remove the bolt

⑵

with a hexagonal tool in one hand; remove the clamp

⑶

and finally remove the direction handle

⑷

CAUTION:

●

Protect protective measures to prevent scratching the appearance of the instrument case and the decorative

cover.

●

When assembling the clamping block, first tighten the 2 bolts at the front, and then tighten the bolts at the rear

(close to the fuel tank side). Wrong sequence or diagonal locking may break the lock block.

Содержание ZT125-Z2













































































Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды

Zontes ZT125-Z2, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-Z2

Отзывы:

Похожие инструкции для ZT125-Z2

Бренды по названию

Популярные бренды